× 1-800-946-2642 Home My Account Social / Forum Articles Contact My Cart
Shop Now
Select Your Car Type Sale Items Clearance Items New Items
The 'stage one' kit is designed for your MINI as an easy to install bolt-on performance option for your stock 998cc Mini engine. Typical result obtained from fitting this kit include 20% more power, 12% more torque, average 47 MPG (Imperial), all of this with no significant noise increase. (The engine will require adjustment after fitting in order to achieve these typical results). The kit includes a Freeflow exhaust manifold, alloy inlet manifold, performance exhaust system and fitting kit, K&N air filter, replacement carb needle (for HS4 carburetor), manifold and carburettor gasket and full fitting instructions.

Fitting Instructions as follows:
Although the 998/1300 stage one kits are bolt on parts, easily fitted by any person with mechanical knowledge, the following must be understood:

1) The engine will require adjustment/tuning after fitment and specialist equipment or knowledge is required. It is advisable to have the car set up on a rolling road and ensure exhaust emissions are correct.
2) The kit is not recommended for vehicles with factory fitted engine management control units, ie 1275cc – 1993 on.
3) Fitting of extra engine/gearbox stabilisers is recommended.

This C-STN17 kit includes: Freeflow exhaust manifold, Mini Spares inlet manifold, RC40 exhaust system and fitting kit, K&N filter element, replacement carburetor needle (spring loaded BIAS type only), manifold gasket, and carburetor gasket.

Remove old exhaust system and combination manifold. Remove carburetor from old manifold.
Undo engine steady bar at engine end and rocker cover to ease fitment of exhaust manifold without disconnecting driveshafts on rod type gearboxes.*
*NOTE - The manifold steady bracket MUST be fitted to diff side plate bolt to avoid manifold breakage. If rubber coupling type is used, it may be necessary to disconnect it.

Fit the inlet manifold BEFORE fitting carburetor. Once manifolds are in place, refit rocker cover and fit carburetor assembly to manifold.
Remove carburetor dashpot and fit new needle.
Remove old air filter element and fit new K&N element. Fit air cleaner to carburetor.
Reconnect engine steady bar.
Remove old exhaust mounts and fit new ones supplied.
Loosely hang RC40 system until best fit is achieved, then tighten all mountings.

TIMING: 5º BTDC, vac disconnected at 1000 rpm(strobe setting). Recheck when engine is warmed up.
MIXTURE: 2•'5f- 3% CO at idle.
1. Standard induction and exhaust system
2. Modified system using MG Metro inlet manifold
3. Modified system using Mini Spares inlet manifold

Results obtained from fitting this kit:
20% more power
12% more torque
Best MPG 55
Worst MPG 42
Average 47

No significant noise increase

c-stn17_bhp Mini Cooper
Mini Mania kits are priced to save you money. Get all of the components you need for less than if purchased separately.
  • Typical result obtained from fitting this kit include 20% more power, 12% more torque, average 47 MPG (Imperial)
Classic Mini 998cc Stage 1 Intake & Exhaust Kit

Classic Mini 998cc Stage 1 Intake & Exhaust Kit

Classic Mini 998cc Stage 1 Intake & Exhaust Kit

Classic Mini 998cc Stage 1 Intake & Exhaust Kit

Classic Mini 998cc Stage 1 Intake & Exhaust Kit
Part No: C-STN17
$501.95
Qty:
Specially Priced. Discounts Do Not Apply.
Fits the following:
Classic Mini
PayPal Pay Later
The 'stage one' kit is designed for your MINI as an easy to install bolt-on performance option for your stock 998cc Mini engine. Typical result obtained from fitting this kit include 20% more power, 12% more torque, average 47 MPG (Imperial), all of this with no significant noise increase. (The engine will require adjustment after fitting in order to achieve these typical results). The kit includes a Freeflow exhaust manifold, alloy inlet manifold, performance exhaust system and fitting kit, K&N air filter, replacement carb needle (for HS4 carburetor), manifold and carburettor gasket and full fitting instructions.

Fitting Instructions as follows:
Although the 998/1300 stage one kits are bolt on parts, easily fitted by any person with mechanical knowledge, the following must be understood:

1) The engine will require adjustment/tuning after fitment and specialist equipment or knowledge is required. It is advisable to have the car set up on a rolling road and ensure exhaust emissions are correct.
2) The kit is not recommended for vehicles with factory fitted engine management control units, ie 1275cc – 1993 on.
3) Fitting of extra engine/gearbox stabilisers is recommended.

This C-STN17 kit includes: Freeflow exhaust manifold, Mini Spares inlet manifold, RC40 exhaust system and fitting kit, K&N filter element, replacement carburetor needle (spring loaded BIAS type only), manifold gasket, and carburetor gasket.

Remove old exhaust system and combination manifold. Remove carburetor from old manifold.
Undo engine steady bar at engine end and rocker cover to ease fitment of exhaust manifold without disconnecting driveshafts on rod type gearboxes.*
*NOTE - The manifold steady bracket MUST be fitted to diff side plate bolt to avoid manifold breakage. If rubber coupling type is used, it may be necessary to disconnect it.

Fit the inlet manifold BEFORE fitting carburetor. Once manifolds are in place, refit rocker cover and fit carburetor assembly to manifold.
Remove carburetor dashpot and fit new needle.
Remove old air filter element and fit new K&N element. Fit air cleaner to carburetor.
Reconnect engine steady bar.
Remove old exhaust mounts and fit new ones supplied.
Loosely hang RC40 system until best fit is achieved, then tighten all mountings.

TIMING: 5º BTDC, vac disconnected at 1000 rpm(strobe setting). Recheck when engine is warmed up.
MIXTURE: 2•'5f- 3% CO at idle.
1. Standard induction and exhaust system
2. Modified system using MG Metro inlet manifold
3. Modified system using Mini Spares inlet manifold

Results obtained from fitting this kit:
20% more power
12% more torque
Best MPG 55
Worst MPG 42
Average 47

No significant noise increase

c-stn17_bhp Mini Cooper
 
 
Question:
Would just want to verify if this would fit a standard 850cc engine?
Answer:
It's possible, yes, but it's really designed for 998's and larger engines. The carb needle in this kit is for an HS4 carb which is big for an 850cc engine.

Mini Mania Tech Team

The Classic Mini Parts and Accessories Experts

 
 
 
 
Question:
I have a 1969 Mini Austin 850 looking at doing a Stage 1 kit to gain some power. Do you supply a kit that would work?
Answer:
While we do not offer a Stage kit for an 850 I might suggest you consider an upgrade to a 998cc

Mini Mania Tech Team

The Classic Mini Parts and Accessories Experts

 
 
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Loading...
Related Technical Articles:
Classic Mini Cooper Exhaust System Stage Kits page 26
Created: January 02, 2019
Upgrade the performance of your engine with your choice of kits that include both intake and exhaust manifolds, etc. Kits available for 998cc, 1098cc & 1275cc engines.
Austin Mini Cooper Engine - 998 TUNING
Created: March 05, 2001
Following on from the easily bolted on performance enhancing components out-lined in the stage one section, we need to consider where to go to get more power output. To improve the 998cc engine out-put, you need to increase the engine's 'breathing' ability. The stage one kit deals with all the easily bolted-on external parts, and represents the best increase for investment.