Classic Mini Cooper Rear Radius Arms Hydrolastic Suspension
Records - of
# |
Part No |
Qty |
Description |
|---|---|---|---|
* Standard fitment, shorter for GDB105, brake drum, longer for GDB106 brake drum with 1" built in spacer |
|||
All wheel nuts shown on drive flange and bearing page. |
|||
| 1 | TRA31 | 1 | Hydrolastic radius arm R/H - Reconditioned |
| 1 | TRA30 | 1 | Hydrolastic radius arm L/H - Reconditioned |
| 2 | 21A1486 | 1 | Stub axle R/H No longer Available |
| 2 | 21A1490 | 1 | Stub axle Left hand side No longer Available |
| 3 | 2A7352 | 2 | Stub axle circlip |
| 4 | LBS507 | 2 | Bush for pivot arm No longer Available |
| 5 | 21A1375 | 2 | Bracket on radius arm for hose No longer Available |
| 6 | ACA9099 | 2 | Radius arm pin |
| 7 | ATJ4098 | 2 | Roller bearing inner, was 13H442 |
| 8 | 2A7325 | 2 | Bronze bush outer |
| 9 | 21A396 | 2 | Metal grease sleeve, replaced by plastic sleeve Use kit GSV1125 |
| 10 | 2A7324 | 2 | Outer thrust washer |
| 11 | ACA9302 | 2 | Inner thrust washer |
| 12 | 2A7327 | 4 | Sealing rubber ring |
| 13 | GFK1128 | 4 | Spring washer, was LWZ208 |
| 14 | FNZ508 | 4 | Nut |
| 15 | UHN400 | 2 | Grease nipple |
| 16 | GSV1125 | 2 | Radius arm repair kit, was 8G7134 |
| 17 | 21A2023 | 1 | Hub without studs |
| 17 | 21A1277 | 1 | Hub with long studs, 1275GT ‘S’ |
| 18 | 21A2064 | 1 | Wheel stud shaft length 1.375" 35mm Thread length 0.875" |
| 18 | 21A2064L | 1 | Wheel stud shaft length 2.000" 50.80mm Thread length 1.125" |
| 18 | 21A1278 | 1 | ‘S’ Wheel stud shaft length 2.25" Thread length 0.875" |
| 18 | ENJO-1039 | 1 | Wheel stud shaft length 2.375" Thread length 1.107 (28mm) |
| 18 | ERA1268 | 1 | Wheel stud shaft length 2.437 Thread length 1.000 |
| 19 | 88G322 | 8 | Wheel nuts, round radius chamfer angle |
| 20 | CN1 | 16 | Chrome wheel nut Alternative to 88G322 |
| 20 | CN4 | 16 | Chrome wheel nut, wide base Alternative to 88G322 |
| 20 | CN2 | 16 | Chrome wheel nut, 60° chamfer angle Weller steel and Rostyle |
| 20 | CN5 | 16 | Chrome wheel nut, wide base Alternative to CN2 |
| 20 | AHA8785 | 16 | Chrome wheel nut, 60° chamfer dome - 1275GT Rostyle Weller steel, use CN2 |
| 21 | GHS134 | 2 | Metal backed ‘S’ rear hub oil seal Use GHS102 |
| 21 | GHS102 | 2 | Rear hub oil seal |
| 22 | GHB116 | 4 | Bearing without built in spacer No longer Available |
| 22 | GHB212 | 4 | Bearing with built in spacer |
| 23 | 2A7354 | 2 | Spacer when GHB116 fitted |
| 24 | GHK1088 | 2 | Bearing kit with built in spacer and seals |
| 24 | GHB147K | 2 | Timken tapered roller bearing set with seals S, and Mini 1984-on |
| 25 | BTA672 | 2 | Hub washer, was 21A1892 |
| 26 | NL610041 | 1 | Hub nut R/H |
| 26 | FNN2410 | 1 | Hub nut L/H Left hand thread- |
| 27 | ATB4098 | 2 | Grease retaining cap |
| 28 | 21A1507 | 2 | Hand brake quadrant |
| 29 | 2K2545 | 2 | Spring washer |
| 30 | 21A1512 | 2 | Thrust washer |
| 31 | 21A1513 | 2 | Spire clip No longer Available |
